view St52 Plate Thickness, DIN 17100 ST52-3 Plate Supplier In India with effective & timely delivery
Table Of Content
- Chemical Composition of DIN 17135 ST 52 Steel Plate
- St52 Steel Plate Mechanical Properties
- Density/Melting Point of St 52 Material
- Thickness Tolerance of DIN 17100 ST52-3 Plate
- St 52 Material Yield and Tensile strength
- ST52-3N Steel plate Flatness Tolerances
- Elongation of Din St52 Steel Plate
- ST 52.3 Plate Standard Sizes in stock
- Characteristics of St52 Plate
- Carbon Steel ST 52.3 Sheet Welding
- Typical Applications of St52 Steel Sheet
The ST 52 belongs to a standard structural steel grade. A St 52 Steel Plate is designed with a superior chemical composition of carbon, silicon, manganese, phosphorous, and sulfur. The content embedded in these plates gives them enhanced resistance to corrosive and oxidative media. The St52 Plate is designed for thickness above 6mm and more. These plates have enhanced resistance to pitting and crevice corrosion. They provide good stability and support to different applications. St52-3 Plate is a low manganese carbon grade that doesn’tputs pressure on subsequent modules. These robust plates can be easily welded in place following standard procedures. The versatile St52 3 Steel showcase slightly lower strength and tolerance compared to an St52 plate. These lightweight components comply with different national and international standards. The St52 Steel Sheet is produced in thicknesses below 6mm and above 0.5mm. These sheets don’t provide stability and add an aesthetical appeal to different components.
A St 52 Steel grade is designed with a density of 7.85 g/cm3 and has a hardness of Brinell 180. The steel has excellent weldability and machinability that is similar to mild grades of steel. The steel modules are commonly seen in the construction of bridges, buildings, general engineering, etc. The 1.0570 Steel works well in extreme and cryogenic temperatures. The steel has good impact resistance and is commonly supplied in the standard normalized condition. The St 52 Material is designed with superior mechanical properties. These components have a minimum tensile strength of 335mpa with a tensile strength between 510 to 630mpa. The items can be easily elongated by 21% in the system. The Plate St52 Equivalent Indian standard is the IS 2062 that is specified by the Bureau of India Standards. To know more about our products or want to get a quote on them, contact us for more information.
Standard |
DIN 17100 steels for general structural purposes |
---|---|
Grade |
1.0570 |
Approval By Third Party |
ABS, DNV, GL, CCS, LR , RINA, KR, TUV, CE |
Dimension |
ASTM/BS EN/DIN/GB/AISI |
Classification |
General structural purposes |
Product Discription |
Hot rolled carbon steel 1.0570 plate |
Thickness |
5mm - 150mm |
Width |
1000mm – 3000mm |
Length |
3000mm -18000mm |
Description | Price |
St52 Anti Slip Diamond Checkered Plate | US $ 500-900 / Ton |
1.0570 Hot Rolled Mild Carbon Plate | US $ 650-920 / Ton |
8mm Thick St52 Hot Rolled Carbon Plate | US $ 320 / Piece |
1.0570 MsPlate 12mm for Container | US $ 620-660 / Ton |
St52 Cold Rolled Carbon Sheet/Plate | US $ 540-660 / Ton |
Hot Rolled 1.0570 Low Carbon Alloy Plate | US $ 500-850 / Ton |
1.0570 Flat Sheet Diamond Plate | US $ 600-800 / Ton |
St52-3 Plate | US $ 800-1000 / Ton |
check Plate St52 Equivalent and St52 Vs C45, according to customer specifications Best range of 1.0570 Steel Plate Stockist in India at dealer price
both are structural steel grades. The St52 3 Steel can be differentiated from each other based on certain characteristics
- The 1.0570 grade contains more molybdenum in its alloying elements than the C45 grade, providing it more resistance.
- Niobium, titanium, and vanadium are present in higher concentrations in the Din 2391 St52 grade than in the C45 grade. These alloying elements help to keep the Din 1629 St 52 stable in a variety of stress-inducing situations.
- When compared to the St52 Din 2391 grade, the C45 grades have better tensile and yield strengths.
- The Din 2448 St 52 grade's adaptable module has better weldability than the C45 grade.

St52-3 Steel Plate

8mm Thick St52 Hot Rolled Carbon Steel Plate

3mm 6mm Thick Mild Steel Plate ASTM St52

St52 Carbon Steel Plate

Hot Rolled Steel Plate St52-3

St52-3 Low-Alloy Steel Sheet and Plate

St52 Low Alloy Hot Rolled Steel Plate

St52 H8-H9 Chrome Plate
if you want a great DIN 17135 ST 52 Steel Plate You've come to the right place, must view Difference Between St52 And St52-3, ST52-3N Steel plate For Sale
Nominal thickness (mm) |
16 - 40 |
to 16 |
40 - 63 |
80 - 100 |
63 - 80 |
150 - 200 |
100 - 150 |
ReH - Minimum yield strength (MPa) |
345 |
355 |
335 |
315 |
325 |
|
|
Nominal thickness (mm) |
3 - 100 |
to 3 |
Rm -Tensile strength (MPa) |
490-630 |
510-680 |
Nominal thickness (mm) |
≥63﹤100 |
≥1<1.5 |
≥0.5 <1 |
≥2﹤2.5 |
≥1.5<2 |
≥3<40 |
≥2.5<3
|
≥40﹤63 |
A - Minimum elongation Lo = 5,65 √ So (%) Longitudinal |
20 |
15 |
14 |
17 |
16 |
22 |
18 |
21 |
- The St52 grade is intended to be slightly stronger than the St52-3 grade.
- The St52-3 grade of low carbon manganese has better weldability than the St52 grade modules.
Please enter values then click on Calculate.
Brinell 180 is the hardness of this CS grade.
cut to size DIN 17100 ST52-3 General structural steel plate Stocking Distributor and Wholesaler , your difficulties will be solved completely Our entire staff can assure you that, we are St 52 Steel Plate Supplier
Thickness | Length x Width | Mass per Sq m |
---|---|---|
mm | mm | Kg / m2 |
1.60 mm | 2500 x 1250 mm | 12.56 Kg / m2 |
2.50 mm | 2500 x 1250 mm | 19.63 Kg / m2 |
1.60 mm | 2000 x 1000 mm | 12.56 Kg / m2 |
2.00 mm | 2000 x 1000 mm | 15.70 Kg / m2 |
1.60 mm | 3000 x 1500 mm | 12.56 Kg / m2 |
2.00 mm | 2500 x 1250 mm | 15.70 Kg / m2 |
2.50 mm | 2000 x 1000 mm | 19.63 Kg / m2 |
2.00 mm | 3000 x 1500 mm | 15.70 Kg / m2 |
2.50 mm | 2440 x 1220 mm | 19.63 Kg / m2 |
This is a flexible grade with excellent tolerances to a variety of pollutants. The versatile grade has a melting point of 1470 degrees and a density of 7.85 g/cm3. The thermal conductivity of these modules is 53 W/mk, while the electrical conductivity is 6.8 IACS.
The tensile strength of St52 Steel Plate Mechanical Properties is 630 MPa, with a yield strength of 380 MPa. The shear strength of these plates is 380 MPa, and they may be easily extended by 13%. The tough modules have a Brinell hardness of 180.
equivalent material | |||||||||||||||||
Germany | US | European Union | UK | France | Japan | China | India | ISO | |||||||||
Steel | Standard | Steel | Standard | Steel (Steel number) | Standard | Standard | Steel | Steel | Standard | Standard | Steel | Standard | Steel | Standard | Steel | Standard | Steel |
St 52 | DIN 17100: 1980 | Grade 50 | ASTM A572/A572M | S355 | EN 10025-2: 2005 | GB/T 1591 | Q345; Q355 | IS 2062 | E350 | ||||||||
St 52-3 | S355J2 (1.0577) | JIS G3135 | SPFC590 | Q355C; Q345C | ISO 630-2 | S355C | |||||||||||
St 52-3U | S355J0 (1.0553) | BS 4360 | 50C | E36-3 | NF A35-501 |
Various Types of 1.0570 Plate

St 52 Steel Plate

DIN 17100 St52-3 Plate

St52 Steel Sheet

Plate St52

1.0570 Steel Plate

ST52-3N Steel plate
know more about Equivalent, Mechanical Properties and Price here, Din St52 Steel Plate Supplier
according to DIN 17100 and DIN EN 10025: 1993 Chemical composition (ladle analysis) of 1.0570
Chemical Composition (ladle analysis), %, ≤ | |||||||||||
Country (Region) | Standard | Steel Grade (Steel number) | P | Si | C | Mn | N | S | Cu | Thickness (d) (mm) | Method of deoxidation |
Germany | DIN 17100: 1980 | St52-3 (1.0570) | 0.040 | 0.55 | 0.20 | 1.60 | – | 0.040 | ≤ 30 | Fully Killded | |
0.22 | 30 <d ≤100 | ||||||||||
European Union | EN 10025: 1993 | S355J2G3 (1.0570) | 0.035 | 0.55 | 0.20 | 1.60 | – | 0.035 | ≤ 30 | ||
0.22 | 30 <d ≤100 | ||||||||||
EN 10025-2: 2004 | S355J2 (1.0577) | 0.025 | 0.55 | 0.20 | 1.60 | – | 0.025 | 0.55 | ≤ 30 | ||
0.22 | 30 <d ≤100 |
Chemical composition (product analysis) of 1.0570 according to DIN 17100 and DIN EN 10025: 1993.
Chemical Composition (product analysis), %, ≤ | |||||||||||
Country (Region) | Steel Grade (Steel number) | Standard | P | Si | C | Mn | N | S | Cu | Thickness (d) (mm) | Method of deoxidation |
Germany | (1.0570) | DIN 17100: 1980 | 0.065 | 0.60 | 0.22 | 1.70 | – | 0.065 | ≤ 30 | Fully Killded | |
0.24 | 30 <d ≤100 | ||||||||||
European Union | S355J2G3 (1.0570) | EN 10025: 1993 | 0.045 | 0.60 | 0.22 | 1.70 | – | 0.045 | ≤ 30 | ||
0.24 | 30 <d ≤100 | ||||||||||
S355J2 (1.0577) | EN 10025-2: 2004 | 0.035 | 0.60 | 0.22 | 1.70 | – | 0.035 | 0.60 | ≤ 30 | ||
0.24 | 30 <d ≤100 |
Thickness (mm) |
Impact Values Charpy-V-Notch Longitudinal Average from 3 Speimens Thk. >10<150mm. |
Tensile Strength Rm min (N / mm²) |
Yield Strength Reh min (N / mm²) |
Elongation A5 min (%) |
3<thk<100 |
27 Joules at -20 C |
490-630 |
315-355 |
max 22 |
this grade is designed with a density of 7.85 g/cm3.
- Material:1.0570
- Density: 7.85 g/cm3
- Melting point: 1420-1460 °C (2590-2660 °F)
Thickness tolerance | Multilayer thickness tolerance | Composite plate strip total thickness tolerance | ||||
Class Ⅲ | Class I, Class II | Composite plate total thickness / mm | tolerance(%) | |||
plate | strip | Class Ⅲ | Class I, Class II | |||
Not more than ten percent of the layer's normal size, and not more than one millimetre | Not more than 9% of the layer's nominal size, and not more than 1mm | 26~30 | — | ±6 | +7 -5 |
|
≥8~15 | — | ±8 | +9 -7 |
|||
— | 4~8 | ±9 | +10 -8 |
|||
16~25 | — | ±7 | +8 -6 |
|||
>60 | — | Negotiate | Negotiate | |||
31~60 | — | ±5 | +6 -4 |
Yield Strength
Yield strength (≥ N/mm2); Thickness (d) mm | ||||||
number | d≤16 | 80< d ≤100 | 40< d ≤63 | >100 | 16< d ≤40 | 63< d ≤80 |
1.0570 | 355 | 315 | 335 | by agreement | 345 | 325 |
Tensile Strength
Tensile strength (≥ N/mm2); Thickness (d) mm | |||
number | d<3 | >100 | 3 ≤ d ≤ 100 |
1.0570 | 515-680 | by agreement | 490-630 |
Composite steel plate total thickness / mm | Width / mm | ||
>1450~1800 | 1000~1450 | >1800 | |
Allowable unevenness / mm within the specified width | |||
>8~25 | 14 | 10 | 15 |
4~8 | 9 | 8 | 10 |
≥26 | 12 | 8 | 14 |
Elongation (≥, %); Thickness (d), mm | |||||
grade | 0.5 ≤d <1 | 1≤ d <1,5 | 1,5≤ d <2 | 2≤ d <2,5 | 2,5≤ d <3 |
St52-3U Plate | 14 | 15 | 16 | 17 | 18 |
St52-3N Plate | 12 | 13 | 14 | 15 | 16 |
Elongation (≥, %); Thickness (d), mm | ||||
grade | 3 ≤d ≤40 | 40< d ≤63 | 63 < d ≤100 | >100 |
St52-3 Plate | 22 | 21 | 20 | by agreement |
St52-3N Plate | 20 | 19 | 18 |
Thickness | Length x Width |
---|---|
mm | mm |
1.6 mm | 2500 X 1250 mm |
3.0 mm | 2000 X 1000 mm |
1.6 mm | 2000 X 1000 mm |
2.0 mm | 2000 X 1000 mm |
1.6 mm | 3000 X 1250 mm |
2.0 mm | 2500 X 1250 mm |
2.5 mm | 2000 X 1000 mm |
2.0 mm | 3000 X 1250 mm |
2.5 mm | 2500 X 1250 mm |
3.0 mm | 2500 X 1250 mm |
- good Machinability
- Case hardening the outer surface using one of the following processes can produce the required hardness:
- Nitrocarburising
- Carbonitriding
- Carburising
- Nitriding
- Tuftriding
This alloy can be successfully welded using typical fusion and resistance procedures, although oxyacetylene welding is not recommended. If filler metal is necessary, AWS E/ER630 is recommended.
- Yellow Goods
- Bridges
- Construction
- Energy
- Engineering
- Rail
- Tanks