Inconel 600 Plate

What is Inconel 600 Plate?

Inconel 600 or as also referred to by its trade name UNS N06600 is a non-magnetic, highly corrosion resistant nickel based alloy. Reckoned as a conventional engineering grade alloy, Inconel is a good fit for use across a wide temperature range.

 

Inconel 600 Plate

Inconel 600 Plate

 Nickel Alloy 600 Sheet

Nickel Alloy 600 Sheet

UNS N06600 Strip

UNS N06600 Strip

Although the mechanical properties could vary at different temperature points. For instance, the minimum tensile strength, in an annealed condition for Inconel grade 600 Sheet, Plate, Strip, Bar at ambient temperature would be 550 MPa, whereas its yield strength at 2% offset stands at 240 MPa with a 30% Elongation in 2". The melting point of Din 2.4816 ranges between 2470 °F - 2580 °F, which explains why these plates can be used to a temperature elevation point of up to 2000 °F.

The impact strength or toughness property of Inconel 600 like its tensile strength, remains unaffected in low temperatures. Hence, the alloy, from a resultant Charpy V-Notch test could be used from temperature as low as -100°F to a temperature as high as 1000°F, with its impact strength ranging between 217 MPa - 244 MPa.

What is ASTM B168 UNS N06600 Sheet?

Usually, components such as plates, sheets, and strips produced from nickel based alloys such as Alloy 600 are made in accordance with ASTM B168. The products made under this particular specification are to be first sampled and prepared, following which they are to be tested for their conformance to not only their chemistry requirements, but also their mechanical as well as their dimensional requirements. In addition to this, the UNS No 6600 plates are also tested to check if they conform to their grain size requirements

 

Werkstoff No 2.4816 Sheet Sizes Metric

Inconel 600 Sheet

0.018" - 0.065"

 

Materials Selection And Specification Of Inconel 600 Plates

Standard ASTM B168 / ASME SB168 
Sizes Available
2000 mm x 2000 mm, 1000 mm x 2000 mm, 2000 mm x 4000 mm, 1500 mm x 3000 mm, 1220 mm x 2440 mm,
Sheet Thickness Range 0.1mm to 12 mm Thk
Basic Form Coils, Rolls, Flats, Strip, Foils, Ring (Flange), Blank (Circle), Shim Sheet, Plain Sheet
Finishes provided Cold rolled sheet (CR), Hot rolled plate (HR), 2D, 2B, SATIN (Met with Plastic Coated), BA NO(8)
Hardness of Alloy 600 Plates Half Hard, Hard, Quarter Hard, Soft, Spring Hard, etc.

 

Typical Mechanical Property Ranges Of UNS N06600 Strip

Element Melting Point Density Elongation Yield Strength (0.2%Offset) Tensile Strength
600 1413 °C (2580 °F) 8.47 g/cm3 40 % Psi – 45,000 , MPa – 310 Psi – 95,000 , MPa – 655

 

Chemical Compatibility Chart Of Nickel Alloy 600 Coil

Grade Si Cu S Cr Mn C Fe Ni
600 0.50 max 0.50 max 0.015max 14.00 – 17.00 1.00 max 0.15 max 6.00 – 10.00 72.00 min

 

ASTM B168 Alloy 600 sheet Equivalent Properties

STANDARD UNS WNR Material Number BS GOST EN JIS AFNOR
600 N06600 2.4816 NA 13 МНЖМц 28-2,5-1,5 NiCr15Fe NCF 600 NC15FE11M

 

Contact Our Experts & Get a Free Quote for Inconel 600 Plates