Nickel 201 Plate

 

 

Do you want to buy Pure Nickel 201 Perforated Sheet from a reliable and experienced stockist? your serach end here and view Thickness Chart In Mm and Nickel 201 Vs Nickel 200

 

Nickel 201 components are designed with commercially wrought alloys. The Nickel 201 Plate shows excellent corrosion resistance properties and can operate in temperatures up to 600 degrees F. The lower carbon content protects these plates against graphitization, making them less susceptible to embrittlement. Apart from this, the plates show excellent resistance to caustic alkalis and varying acid systems to give these modules enhanced oxidation resistance in stress-induced environments.

The AMS 5553 is a specification that covers low carbon nickel alloy 201 produced in the form of sheet and strip. The included a nominal thickness ranging between 0.001 to 0.250 inch.

The melting point of UNS N02201 is high and ranges between 1435°C - 1446°C. In an annealed condition the yield strength of grade 201 nickel plate is 14900 psi, whereas its Rockwell hardness is valued at 85. Alloy 201 is well suited to be used for Marine and offshore engineering applications due to its excellent performance in flowing seawater even when the alloy has been exposed to high velocity conditions. In comparison to cold worked Alloy 201 Strips, both hot-rolled and annealed strips are known to have a higher impact strength.

 

This specification takes into consideration components such as coil, plate, sheet, and strip made from low carbon nickel based alloy i.e. grade UNS N02201. Along with conforming to the chemical requirements of the specification, these plates need to conform to the mechanical property requirements as well. Moreover, this specification makes provisions for deep drawing and spinning quality Werkstoff Nr. 2.4068 sheet and strip which needs to conform to values pertaining to the other additional properties like grain size and hardness properties. Hence, the Ni 201  produced will be required to undergo several tests to check their conformance to this specification.

 

The availability of stock in factories helps in determining the delivered date from the date of receiving the order. If these modules are unavailable then the time will be substantially higher depending on the requirement. Since we are tied with the best logistical partners, the Pure Nickel plates in Australia and Canada can be shipped and delivered to the location within 5-6 days from the date of order. Delivery in South Africa will take at least 8-9 days from the date of order.

 

Sheets and plates are basic and versatile components exhibiting excellent properties if purchased from the right suppliers. ASTM B162 Alloy 201 Chequered Plate are high-quality modules designed to outperform and outshine other steel. Designed with good content of nickel these products are highly resistant to corrosive media. These plates are subjected to various testing procedures before they are shipped to ensure customers get the best. All the products can be cut in size or sawed as per the requirements of the buyer. The affordable rate coupled with all these features makes Triton a very good prospect to buy these modules.

 

Nickel 200 and 201 sheets have identical properties and capacities to fight against oxidative and corrosive systems. The major differentiating factor in both these modules is the concentration of carbon. A nickel 200 sheet has a carbon content of 0.15%, while a nickel 201 sheet has a carbon content of 0.02%. The lower carbon content allows these modules to be utilized in systems where other grades are susceptible to embrittlement.

 

In India and abroad, we have a large supply network for ASME SB162 NW 2201 Coil and Foil, WERKSTOFF NR. 2.4068 Clad Plate Dealer with widths ranging from 1250mm to 2500mm or as required by customers.

 

Sheets and plates are two distinct shapes across the nickel grade. A Pure Nickel 201 Plate is designed with a thickness of above 6mm. These modules provide stability and rigidity to the different modules. Ni 201 Sheet is designed with a thickness of less than 6mm. These modules don’t provide stability but add an aesthetical appeal to the module.

 

Quality is the best solution to all problems. Ni-201 Strip is subjected to vigorous testing and screening to eliminate any defects or damage within these strips before they go to the real world. The Nickel 201 Strip is subjected to tension and bend testing. These strips are also put through ultrasonic testing, hardness, and Charpy V-notch testing to check for optimum toughness.

 

UNS N02201 Perforated Sheet is an aesthetically appealing module available in a range of sizes. The UNS N02201 Perforated Sheet can be availed in all standard sizes of plates, sheets, coils, and so on. To get all these components in custom sizes, the Pure 201 Nickel Shim Sheet can be cut in specified shapes to meet all the project requirements.

 

Coils and foils are two shapes ASTM B1662 components can be shaped into. A WERKSTOFF NR. 2.4068 Foil is the thinnest module within this grade designed with a thickness of less than 0.2mm. These modules provide protection and insulation to different modules during transport and heat treatment. ASME SB162 NW 2201 Coil is rolled and wound after the rolling process in thickness between 1.2mm to 20mm. These modules can be effectively transported from place to place and later sheared into appropriate sizes.

 

 

 

 

Stockholder of Nickel 201 Sheet In India, Pure 201 Nickel Shim Sheet is available in a variety of finishes, including No. 8 mirror finish, BA, and No. 4 matte finish, with or without PVC coating.

 

 

 

 

 

As Distributors stock a large quantity of hot and cold rolled ASTM B162 Alloy 201 Chequered Plate for usage in the marine industry.

 

 

 

 

• Salt production
• Caustic handling equipment
• Marine and offshore engineering
• Food processing equipment